Spares Parts

Understanding that each aspect is of critical importance in air atomizing, we are offering a range that finds application in continuous casting, cooling castings and moulds, curing concrete products, evaporative coolers, foam control, incineration, quenching, spray coating, spray drying, flue gas desulfurisation and many more.

Technical Specifications

• Internal mix design, with a range of flow and spray angles.
• High turn down ratio.
• Variation on degree of atomization.
• Siphon/gravity fed design with external mixing of air and liquid.
• Pressure fed design with external mixing of air and liquid.

Constructional Options

• Siphon/gravity fed design with external mixing of air and liquid.
• Siphon/pressure fed design with external mixing of air and liquid.
• Pressure fed design with internal mixing of air and liquid.

C-series centrifugal pumps find application throughout sanitary and industrial processes. These rugged pumps accommodate a wide range of solid and liquids under a variety of flow conditions and deliver long service with minimum downtime.

Specifications

• 304 stainless steel adapters - standards, eliminate the rust, corrosion and chipping paint of convenient carbon steel adapters.
• Tested performance - every pump passes strict testing before release for shipping.
• Longer seal life - wave spring provides more uniform loading on seal face than single coil spring, hydraulic balancing reduces sealing surface pressures for lee wear and less downtime.
• CIP capability - grooves-in-impeller/shaft routes CIP chemical solutions to all critical areas for clean-in-place.
• Fast, easy take down - no tools required, quick opening, heavy duty cast clamp secures casing, impeller pin retained by centrifugal force.
• Casing matches job - choose from standard or enlarged inlet with port connection that meets your piping system.
• Wave spring extends seal life - wave spring maintains uniform loading on seal faces for longer seal service.
• Motor - Standard C-face; 3 phase, 230/460 volts, 1750 and 3500 RPM, TEFC and Washdown Duty, Foot Mounted Other Motor Types upon request.

The range of micro fitting and valves that we offer is being widely used in leak tight applications including vacuum to positive pressure applications. It is most suitable for product range that requires high purity and ultra high purity specifications.

Semi welded plates are built up in plate cassettes. A plate cassette is 2 plates welded together by means of laser welding. The advantage by this construction is on the one side welded plate channel and on the other side a traditional plate channel with gaskets making assembling and cleaning of this side easier. On the welded side there are two specially produced corner hole gaskets creating the tightening between the two cassettes. Thus the gasket is reduced to a minimum on the welded side.
Advantages and applications

• Laser welded plates
• Suitable for NH3
• Evaporators and condensers
• High working pressure
• Minor gasket area
• Safe operation without leaking
• Small liquid volume

EDT provides the technical knowledge to design adequate Fire Suppression Systems relative to your spray drying equipment.

Fire suppression systems require strategic placement of fire nozzles for sample water deluge that will protect equipment in the case of fire. EDT liquid-activated fire suppression nozzles provide this deluge by utilizing a specially designed spray head that fully extend under liquid pressure during fire suppression system activation.

Our complete fire suppression system includes EDT liquid-activated fire suppression spray nozzles, dump valves, water valves, controls and installation.

Dump valves in our fire suppression system provide an outlet for water drainage to prevent components from filling with water, which can damage the structural support of the component.

Fire Suppression Spray Nozzle
EDT’s fire suppression spray nozzle follows the same concept as our CIP Spray Nozzle. The fire nozzle is a retractable, liquid-activated design. Our specially designed spray head extends under liquid pressure and remains stationery providing constant water deluge as long as the system is activated. The fire suppression spray nozzle is constructed of stainless steel and is USDA Accepted for sanitary applications.

Sanitary Dump Valve
EDT sanitary dump valves are raising the standards in equipment protection.

The dump valve will reduce and prevent structural damage to the building and drying equipment that is caused by equipment becoming weighted with water during fire suppression activation. EDT’s dump valve is specifically designed with a powerful long stroke to freely relieve components of dousing water, therefore, preventing water collection. Dump valves are placed on cyclones, baghouses, and other equipment that do not have an open discharge for water to escape.

EDT’s sanitary dump valve is constructed of stainless steel in accordance to USDA guidelines.